OEM Brake Specifications
2017 Land Rover Range Rover Evoque Brake Pad & Rotor Specs
L538 / L551 Platform · Premium Ceramic (Low Dust, Silent Cold Bite)
D1210
Front Pad FMSI
D1211
Rear Pad FMSI
26.0 mm
Front Discard
28 ft-lb
Pin Torque
Critical Mechanic Safety Advisory:
This vehicle utilizes an Electronic Parking Brake (EPB) system on the rear axle. You must engage EPB Maintenance Retraction Mode via the instrument cluster or an OBD-II scan tool before compressing rear pistons. Compressing pistons with a mechanical C-clamp will break the internal plastic planetary gears inside the actuator motor, necessitating full caliper replacement.
Select Land Rover Range Rover Evoque Model Year (2012–2026):
Recommended Brake Replacement Hardware & Diagnostic Tools
Direct OEM Fit
2017 Land Rover Range Rover Evoque Front Ceramic Brake Pads
Precision molded to FMSI D1210 shape. Features dual-layer rubberized shims for whisper-quiet stops and ultra-low light gray brake dust.
Best Value Kit
Front & Rear Rotors + Ceramic Pads Complete Bundle
Geomet anti-rust coated vented rotors (305 mm front / 281 mm rear) bundled with premium low-dust ceramic pads.
Diagnostic Service
OBD-II Scanner with EPB Service Mode Retraction
Retract electric parking brake calipers safely with one touch to prevent expensive actuator motor shear and dash warning faults.
Essential Chemical
OEM 100% Synthetic Silicone Ceramic Brake Pin Grease
Pure non-petroleum high-temperature silicone lubricant rated to 3,000°F. Will never swell or tear rubber caliper slide pin boots.
Disclosure: SelectMyBlog participates in the Amazon Services LLC Associates Program. Clicking verified merchant product links earns an affiliate commission at zero additional cost to you.
2017 Land Rover Range Rover Evoque Factory Brake System Specifications
| Component & Engineering Parameter | Factory Specification |
|---|---|
| Front Brake Pad Standard (FMSI) | D1210 (Dual-Caliper Pad Set) |
| Rear Brake Pad Standard (FMSI) | D1211 (Dual-Caliper Pad Set) |
| Front Rotor Outer Diameter | 305 mm (12 inches) · Ventilated Cast Disc |
| Rear Rotor Outer Diameter | 281 mm (11.1 inches) · Solid/Vented Disc |
| Front Rotor Minimum Discard Thickness | 26.0 mm (Discard if below) |
| Rear Rotor Minimum Discard Thickness | 8.5 mm (Discard if below) |
| Caliper Guide Slide Pin Torque | 28 ft-lbs (38 Nm) (Clean & Lube) |
| Caliper Carrier Bracket Mounting Bolt Torque | 85 ft-lbs (115 Nm) (Blue Threadlocker) |
| Parking Brake System Architecture | Electronic (EPB) · Maintenance Mode Required |
| Specified Hydraulic Brake Fluid | DOT 4 LV (Glycol-Based Hydraulic Standard) |
| DIY Installation Difficulty & Time | Moderate DIY · Approx 45–60 mins (per axle) |
Deep Technical Inspection & Diagnostic Protocol
1. Caliper Slide Pin Torque vs Carrier Bracket Mounting Bolts
Floating brake calipers utilize two separate classes of threaded fasteners that perform distinct mechanical roles. Caliper slide pin guide bolts require light torque (28 ft-lbs). Over-torquing snaps the hollow slide pin threads. Conversely, caliper carrier bracket bolts withstand the entire rotary braking leverage of the vehicle and demand 85 ft-lbs. Clean old debris from the bracket bolt threads and apply medium-strength blue threadlocker prior to assembly.
2. Measuring Past the Outer Rust Lip with a Pointed Micrometer
As brake pads wear against cast iron rotors, an unworn outer perimeter lip develops on the outer rim of the disc. Measuring rotor thickness with standard flat digital calipers produces a false reading up to 1.5 mm thicker than actual friction track depth. Mechanics must utilize a specialized pointed-anvil rotor micrometer that reaches over the ridge directly onto the center wear track. Discard front rotors immediately if measurements reach 26.0 mm.
3. Preventing Disc Thickness Variation (DTV) & Hub Rust Scale
A pulsating brake pedal is almost never caused by thermally warped metal discs; it originates from Disc Thickness Variation (DTV) triggered by lateral runout exceeding 0.002 inches (0.05 mm). Mounting new rotors over an uncleaned wheel hub with surface rust scale causes the rotor to spin with a slight wobble, grinding thin spots into the rotor faces over 3,000 miles. Always wire-brush the hub mounting flange down to bare metal.
4. Structured 10-Step Pad Bedding-In (Burnishing) Protocol
Establishing an even boundary friction transfer layer onto the new cast iron surface is mandatory for quiet operation. Perform 5 moderate stops from 45 mph down to 15 mph with 30 seconds of cooling between cycles. Follow immediately with 5 firm decelerations from 55 mph down to 10 mph without triggering ABS or coming to a full stop. Cruise at highway speeds for 10 minutes without braking to allow the thermal transfer layer to cure completely.
Frequently Asked Questions: 2017 Land Rover Range Rover Evoque Brake System
What is the factory brake pad FMSI number for a 2017 Land Rover Range Rover Evoque?
The factory front brake pad FMSI shape specification for the 2017 Land Rover Range Rover Evoque is D1210, while the rear brake pad shape is D1211. Always cross-reference this standardized FMSI number when ordering replacement ceramic or semi-metallic friction pads.
What is the minimum discard thickness for Land Rover Range Rover Evoque brake rotors?
The minimum allowable discard thickness for front rotors is 26 mm, and 8.5 mm for rear rotors. If rotor thickness drops to or below this limit at any point on the friction track, the rotor must be discarded immediately because it lacks sufficient thermal mass to dissipate heat safely.
What is the caliper slide pin guide bolt torque specification?
Tighten the floating caliper slide pin guide bolts to exactly 28 ft-lbs (38 Nm). Over-torquing slide pin bolts can snap the pin threads or strip the mounting bracket ears. Always clean the slide bores and coat the pins with high-temperature 100% silicone ceramic brake grease.
What is the torque specification for the caliper mounting bracket bolts?
The heavy caliper carrier bracket mounting bolts require 85 ft-lbs (115 Nm). These structural fasteners withstand the entire stopping torque leverage of the vehicle. Clean old debris from the bolt threads and apply medium-strength blue threadlocker before torquing.
Can I push the rear brake caliper piston back with a standard C-clamp?
Yes. The 2017 Land Rover Range Rover Evoque is equipped with an Electronic Parking Brake (EPB) on the rear calipers. You must activate EPB Service Mode through the vehicle dashboard cluster menu or an OBD-II diagnostic tool to retract the internal electric servo motor before pushing the piston back. Never force the piston with a C-clamp, or you will crack the plastic planetary gears inside the servo motor.
Should I install ceramic or semi-metallic brake pads on my 2017 Land Rover Range Rover Evoque?
For daily highway commuting and city driving, Premium Ceramic (Low Dust, Silent Cold Bite) is strongly recommended for virtually silent stops, cold morning initial bite, and ultra-low light gray dust that will not stain alloy wheels. For heavy towing or aggressive mountain descents, semi-metallic pads offer superior thermal fade resistance past 1,000°F.
Why must I measure rotor thickness with a pointed micrometer instead of flat calipers?
As brake pads wear against the rotor surface, an unworn raised ridge or rust lip forms along the outer perimeter edge. Flat caliper jaws span across this lip, producing a false reading up to 1.5 mm thicker than reality. A specialized pointed-anvil brake micrometer steps past the rust lip directly onto the true friction track.
How do I properly bed in (burnish) new brake pads on this vehicle?
Perform 5 moderate stops from 45 mph down to 15 mph with 30 seconds of cruising between stops. Immediately follow with 5 firm, aggressive decelerations from 55 mph down to 10 mph without locking up the wheels or coming to a complete standstill. Drive at highway speed for 10 minutes without braking to allow the transfer layer to cure evenly.
What type of brake fluid is specified for the 2017 Land Rover Range Rover Evoque?
The hydraulic braking system specifies fresh DOT 4 LV. Never mix mineral-based oils or silicone DOT 5 fluids with glycol DOT 3, DOT 4, or DOT 5.1 systems. Flush the brake hydraulic fluid every 24 to 36 months to prevent moisture contamination and internal caliper piston corrosion.
How long does a complete brake pad and rotor replacement take on this vehicle?
A standard DIY axle replacement requires approximately 45–60 mins (per axle) with a difficulty rating of Moderate DIY. Replacing pads and rotors at home saves $250 to $550 per axle compared to dealership and specialty repair shop service labor rates.